Share the love!

These festive Faux Leather Bow Ornament Earrings made with a Cricut are the perfect holiday accessory!

The SVG file is available in my shop if you want to make this project!

Ready to get started? Let’s dive into the materials and steps!

Step 1: Get the SVG Template

Step 2: Shop the Supplies

This page contains some affiliate links (which means if you make a purchase after clicking a link, I will earn a small commission at no additional cost to you). Read my full disclosure policy here.

Compatible Machines✅: Cricut Maker series, Cricut Explore series, Cricut Joy Xtra, Cricut Joy 2, Cricut Joy
Not Compatible Machines❌: none
Blade Used: Standard Fine Point Blade
Cut Setting Used✂️: Faux Leather (Paper Thin) with “More” pressure

• Faux Leather & Heat Transfer Vinyl
• I used this print for the base layer and this plaid for the bow and trees. For both prints I ordered 9×12 sheets, Regular Print, Portrait Orientation.
• I used Siser Glitter HTV in Old Gold for the ornament tops.
• Other Project Supplies
  • 6mm x 6mm Rivets (includes rivet tools) and a hammer
  • Craft glue or fabric glue to glue the tree to the ornament. I used Beacon Fabri-Tac.
  • Earring Hooks
  • 6mm Jump Rings
  • Flat nose jewelry pliers and chain nose jewelry pliers
• Other Cricut Supplies
  • Blue Painters Tape
  • Small Curved Scissors
  • Teflon Sheets
  • Purple Strong Grip Mat
  • Green Standard Grip Mat
  • Cricut EasyPress Mini
  • Heat Pressing Pad, I use an 8×10 size
  • Weeding Tool like a Pin Pen or like the one in the Cricut Basic Tool Set

🛒 To shop many of these supplies below in my Amazon storefront, click here.

Step 3: Make the Project

Set Up Your Design

1. Open a new canvas in Cricut Design Space.
2. Upload the Ornament Bow Earrings SVG to your canvas.
3. Select all of the layers and make them the same color if you want to cut them all on the same mat.
4. Or you can leave them colored as is and cut each mat separately.

Prepare to Cut

1. Click Make It.
2. Mirror your mat(s), since you’ll be cutting faux leather face down.
3. Position your faux leather shapes apart on the mat if cutting from different prints.
4. Choose the Faux Leather (Paper Thin) setting with More pressure.

Cut the Faux Leather

1. Place the faux leather pretty side down on a Strong Grip (purple) mat.
2. Secure all edges with blue painter’s tape.
3. Load the mat into your Cricut.
4. Press the C button to begin cutting.
5. When the cut is complete, without unloading the mat, use a sharp tool to gently lift the edge and check the cut.
6. Repeat the cut if necessary by pressing the cut button again.
7. Once the cut is complete, unload the mat and remove the shapes.

Cut the Heat Transfer Vinyl

1. Return to Design Space and cut the heat transfer vinyl mat using the manufacturer’s recommended cut setting for the brand and type of heat transfer vinyl.
2. Weed away the excess vinyl.

Press the HTV onto the Earrings

1. Preheat an Easy Press to 265 degrees or set an Easy Press Mini to the Low setting.
2. Place the faux leather on a heat pressing pad and layer the HTV shape at the top of the ornament.
3. Cover with a Teflon sheet or cover sheet.
4. Press for 5-7 seconds. Remove the Teflon sheet and try to peel away the clear vinyl cover sheet.
5. If the vinyl lifts up, cover and press again in 5 second increments.
6. Repeat with the other earring.
7. Place the warm earring shapes under your heat pressing pad to cool flat for 1-2 minutes.

Attach the Bow with Rivets

1. Push a 6mm rivet post from the through the second hole from the top on the earring shape, from the back to front.
2. Place the bow shape onto the rivet post.
3. Press a rivet cap on the end of the rivet post. Then use the rivet tools & a hammer to secure the rivet tight.

📺You can watch a video tutorial that shows how to apply 6mm rivets here.

Attach Trees & Earring Hooks

1. Apply the trees to the center of the ornament with fabric or craft glue.
2. Check the placement on both trees while the glue is still wet to make sure the placement is the same on both earrings.
3. Use flat nose jewelry pliers and 6mm jump rings to attach the earrings to earring hooks.
4. Turn the bottom loop on the earring hook 90 degrees so the earrings will hang straight on the ears.

Your Bow Ornament Earrings are complete! Enjoy these festive holiday earrings all season long.

Answers to your questions about making Bow Ornament Earrings

Q: Which Cricut machines will cut faux leather?
A: You can cut faux leather with any of the current Cricut machines because they all cut faux leather with the standard fine point blade included with each machine. For this project you can use any of the Cricut Maker series machines, the Cricut Explore series machines, the Cricut Joy Xtra, the Cricut Joy 2, or the Cricut Joy.

Q: What do I need to press heat transfer vinyl onto faux leather?
A: To press heat transfer vinyl onto faux leather you’ll need a traditional heat press, Cricut EasyPress, or Cricut EasyPress Mini. I used a Cricut EasyPress Mini for this project because it’s great with pressing small projects like earrings, keychains, and accessories. I set the EasyPress Mini to the Low setting and covered the HTV on the faux leather with a Teflon sheet before pressing for about 10 seconds. For a larger EasyPress I set it to 265 degrees F.

Q: How do I get the SVG template for this project?
A: Get the SVG file from my SVG Shop here.

Until next time… and happy creating!

Pin this project to your favorite Pinterest board!

Share the love!